Sahakar Agencies

: + 91 20 25464825

Teknic

.....................................................................................................................................

Conduit Pipe

Features

Safe: Conduit locking around its entire peimeter

Watertight: Protection up to IP68
Control Station

Characteristics of Control Stations

Ambient air temperature Storage -40…+70 Operation -25... + 70

Degree of Protection IP65

Conforming to Standards IEC 947-5-1

Material and Colours Plastic Polyester, white(top) and black(bottom) yellow(top) and black(bottom)

Metalic Cast Aluminum, synthetic enamel paint Silver

Hammertone(top) and Black

Hammertone(bottom) Grey

RAL 7032(top & Bottom) Opal

Green IS275(top & bottom)

Cable Entries Plastic "knock-outs" for no.13 cable glands(PG13.5)

Metalic tapped hole suitale for PG13

cable glands, 3/4" tapped.
Drag Chain

Teknic Plastichains cable Drag Chains are suitable for protection to the various power lines of machinery in motion.

Due to the design features, the plastic chains carriers withstand high level travel speeds & allow high speed acceleration and deceleration.
MCB and DB

Teknic establishesa technical coperation with SEZ KROMPACHY, EU (European Union) for Minature Circuit Breaker, Residual Ciircuit Breaker, Residual Circuit Breaker with Overcurrent Protection.

The advantages of Teknic MCB/ RCCB/RCBO’s:

The MCb’s have window with colour designing the operation status of the MCB.

The Handles of the Dollies of the circuit Breaker with tripping characteristics B, C, D, M and DC are supplied in Black colour.
Metal Push Button

This range of 22.5 mm dia series push button, selector actuators, illuminated push buttons, and pilot lights, in engineering metal construction.

Features

Economy of space

Aesthetically elegant

Self wiping contacts

Robust in the material of construction

Larger operating surfaces

Simple to fix

Safe in Operation
Microswitch

Miniature, snap action, Micro switch MS30 is built with the same features of MS31 and with low force actuation.

Single pole, snap action, change over contacts which may be used to provide a double throw switch to change from one circuit to another with a common supply line, or may be used as normally open or normally closed switches. The changeover time in all cases is fairly independent of the plunger speed.
MPCB

Teknic MPCB are fuseless protection devices mechanism for inductive loads for protection against thermal overloads, short circuit and phase failures. These MPCB’s are cost effective solution for protection of motor with trip class 10, and breaking capacity upto 50 KA.

Main Characteristics of our MPCB Type TMP :

Overload Protection –trip Class 10.

Phase Failures sensitivness

Disconnect function for safety isolation of the installation and the supply

Adjustable Overload Setting (0.8-1).

Suitable for single phase and three phase.

Trip Free Mechanism

Padlocking
Multiple Limitswitches

Teknic Euchner Precision Single and ultiple Limit Switches are used for controlling and postioning of machines and Industrial Equipments.

Minimum space requirement due to compact design, low cost connection through the use of a common wiring cable, reduction in the number of sealing glands for cable entry, cross connection of switch elements with additional termination boxes and easy access to all switch stations for test, adjusting and service purposes.
Plastic Push Button

This range of 22.5 mm dia series push button, selector actuators, illuminated push buttons, and pilot lights, in engineering plastic construction.

Features

Economy of space

Aesthetically elegant

Self wiping contacts

Robust in the material of construction

Larger operating surfaces

Simple to fix

Safe in Operation
Plug Sockets

Industrial Plugs and Sockets

The plugs and sockets are manufactured under the STN EN 60309-1,2 norms which comply with European norms EN60309.

The Plugs and Sockets are of circular shape and can be used within the following ranges:

Nominal current upto 125A

Nominal Voltage upto 500V

Nominal Frequency of 50 or 60Hz

Temperature ranges between -25c to 40c

Features:

1. Insulation Resistance and Dielectric strength of the devices msut be sufficent.
2. Non-blocked devices must have adequate disconnecting capacity.
3. Nominal Operationat requirement
4. Mechanical resistance
5. Heat and combustion resistance.
6. Resistanceof rubber and thermoplastics to ageing.
Proximity Switch

The Teknic Euchner Inductive Proximity Switches are solid state switching devices which require no physical contact to actuate them.

Used for control and positioning signals , these sensors can be connected directly into conventional system or electronic control system.

The Main Advantages for Inductive Sensors are :

Exceptionally long Life.

High Switching Speeds.

No-touch, Zero, operation force

No wear tear, maintence free operation

Bounce free Signals

Reliable Switching under Extreme conditons

Fully Waterproof.
Rocker Switch

Teknic Rocker Switches are menat for switching Inductive, capacitive, Resistive loads to extent of the current and voltage ratings specified.

Teknic Rocker switches are meant for Operation in temperature ranges form Ambient temperature to 85C.

Materials of Construction :

1. Housing : Nylon 66
2. Rocker Button : Polycarbonate Nylon 66
3. Terminals : Copper
4. Contacts: Silver Alloy.
Single Limit Switch

The Tehnic Euchner Limit Switches are designed with robust contruction for Postioning and industrial applications.

The Stainless steel hardened plunger with telescopic action is precisely guided within anodised die casting light aloy load head and is practically maintenance free.

In Switches with plunger applications , the plunger area is seperated from the switch chamber by a diaphragm seal made from NDR Elastomer. The limt switches can be provided even with indicators in 220VAC and 24VDC.
Terminal Strip

TECHNICAL DATA

Housing : Nylon 66

Electrical hardware : Copper Alloy. screws Mild Steel

Conductor size : 0.5 - 2.5sq.mm(for TSS 21 & 22)/4 sq.mm(for TSS 41)

Initial insulation resistance : > 100 megohms.

Measured at 500V

Di-electric strength : Can withstand 2KV for 1 Minute Between Terminal to Body, and between open terminals.

Teknic

Conduit Pipe

Control Station

Drag Chain

MCB and DB

Metal Push Button

Microswitch

MPCB

Multiple Limitswitches

Plastic Push Button

Plug Sockets

Proximity Switch

Rocker Switch

Single Limit Switch

Terminal Strip